1 files changed, 367 insertions, 0 deletions

diff --git a/examples/stm32h5/src/bin/usb_uac_speaker.rs b/examples/stm32h5/src/bin/usb_uac_speaker.rs
new file mode 100644
index 000000000..6b992690f
--- /dev/null
+++ b/examples/stm32h5/src/bin/usb_uac_speaker.rs
@@ -0,0 +1,367 @@
+#![no_std]
+#![no_main]
+
+use core::cell::RefCell;
+
+use defmt::{panic, *};
+use embassy_executor::Spawner;
+use embassy_stm32::time::Hertz;
+use embassy_stm32::{bind_interrupts, interrupt, peripherals, timer, usb, Config};
+use embassy_sync::blocking_mutex::raw::{CriticalSectionRawMutex, NoopRawMutex};
+use embassy_sync::blocking_mutex::Mutex;
+use embassy_sync::signal::Signal;
+use embassy_sync::zerocopy_channel;
+use embassy_usb::class::uac1;
+use embassy_usb::class::uac1::speaker::{self, Speaker};
+use embassy_usb::driver::EndpointError;
+use heapless::Vec;
+use micromath::F32Ext;
+use static_cell::StaticCell;
+use {defmt_rtt as _, panic_probe as _};
+
+bind_interrupts!(struct Irqs {
+    USB_DRD_FS => usb::InterruptHandler<peripherals::USB>;
+});
+
+static TIMER: Mutex<CriticalSectionRawMutex, RefCell<Option<timer::low_level::Timer<peripherals::TIM5>>>> =
+    Mutex::new(RefCell::new(None));
+
+// A counter signal that is written by the feedback timer, once every `FEEDBACK_REFRESH_PERIOD`.
+// At that point, a feedback value is sent to the host.
+pub static FEEDBACK_SIGNAL: Signal<CriticalSectionRawMutex, u32> = Signal::new();
+
+// Stereo input
+pub const INPUT_CHANNEL_COUNT: usize = 2;
+
+// This example uses a fixed sample rate of 48 kHz.
+pub const SAMPLE_RATE_HZ: u32 = 48_000;
+pub const FEEDBACK_COUNTER_TICK_RATE: u32 = 31_250_000;
+
+// Use 32 bit samples, which allow for a lot of (software) volume adjustment without degradation of quality.
+pub const SAMPLE_WIDTH: uac1::SampleWidth = uac1::SampleWidth::Width4Byte;
+pub const SAMPLE_WIDTH_BIT: usize = SAMPLE_WIDTH.in_bit();
+pub const SAMPLE_SIZE: usize = SAMPLE_WIDTH as usize;
+pub const SAMPLE_SIZE_PER_S: usize = (SAMPLE_RATE_HZ as usize) * INPUT_CHANNEL_COUNT * SAMPLE_SIZE;
+
+// Size of audio samples per 1 ms - for the full-speed USB frame period of 1 ms.
+pub const USB_FRAME_SIZE: usize = SAMPLE_SIZE_PER_S.div_ceil(1000);
+
+// Select front left and right audio channels.
+pub const AUDIO_CHANNELS: [uac1::Channel; INPUT_CHANNEL_COUNT] = [uac1::Channel::LeftFront, uac1::Channel::RightFront];
+
+// Factor of two as a margin for feedback (this is an excessive amount)
+pub const USB_MAX_PACKET_SIZE: usize = 2 * USB_FRAME_SIZE;
+pub const USB_MAX_SAMPLE_COUNT: usize = USB_MAX_PACKET_SIZE / SAMPLE_SIZE;
+
+// The data type that is exchanged via the zero-copy channel (a sample vector).
+pub type SampleBlock = Vec<u32, USB_MAX_SAMPLE_COUNT>;
+
+// Feedback is provided in 10.14 format for full-speed endpoints.
+pub const FEEDBACK_REFRESH_PERIOD: uac1::FeedbackRefresh = uac1::FeedbackRefresh::Period8Frames;
+const FEEDBACK_SHIFT: usize = 14;
+
+const TICKS_PER_SAMPLE: f32 = (FEEDBACK_COUNTER_TICK_RATE as f32) / (SAMPLE_RATE_HZ as f32);
+
+struct Disconnected {}
+
+impl From<EndpointError> for Disconnected {
+    fn from(val: EndpointError) -> Self {
+        match val {
+            EndpointError::BufferOverflow => panic!("Buffer overflow"),
+            EndpointError::Disabled => Disconnected {},
+        }
+    }
+}
+
+/// Sends feedback messages to the host.
+async fn feedback_handler<'d, T: usb::Instance + 'd>(
+    feedback: &mut speaker::Feedback<'d, usb::Driver<'d, T>>,
+    feedback_factor: f32,
+) -> Result<(), Disconnected> {
+    let mut packet: Vec<u8, 4> = Vec::new();
+
+    // Collects the fractional component of the feedback value that is lost by rounding.
+    let mut rest = 0.0_f32;
+
+    loop {
+        let counter = FEEDBACK_SIGNAL.wait().await;
+
+        packet.clear();
+
+        let raw_value = counter as f32 * feedback_factor + rest;
+        let value = raw_value.round();
+        rest = raw_value - value;
+
+        let value = value as u32;
+
+        packet.push(value as u8).unwrap();
+        packet.push((value >> 8) as u8).unwrap();
+        packet.push((value >> 16) as u8).unwrap();
+
+        feedback.write_packet(&packet).await?;
+    }
+}
+
+/// Handles streaming of audio data from the host.
+async fn stream_handler<'d, T: usb::Instance + 'd>(
+    stream: &mut speaker::Stream<'d, usb::Driver<'d, T>>,
+    sender: &mut zerocopy_channel::Sender<'static, NoopRawMutex, SampleBlock>,
+) -> Result<(), Disconnected> {
+    loop {
+        let mut usb_data = [0u8; USB_MAX_PACKET_SIZE];
+        let data_size = stream.read_packet(&mut usb_data).await?;
+
+        let word_count = data_size / SAMPLE_SIZE;
+
+        if word_count * SAMPLE_SIZE == data_size {
+            // Obtain a buffer from the channel
+            let samples = sender.send().await;
+            samples.clear();
+
+            for w in 0..word_count {
+                let byte_offset = w * SAMPLE_SIZE;
+                let sample = u32::from_le_bytes(usb_data[byte_offset..byte_offset + SAMPLE_SIZE].try_into().unwrap());
+
+                // Fill the sample buffer with data.
+                samples.push(sample).unwrap();
+            }
+
+            sender.send_done();
+        } else {
+            debug!("Invalid USB buffer size of {}, skipped.", data_size);
+        }
+    }
+}
+
+/// Receives audio samples from the USB streaming task and can play them back.
+#[embassy_executor::task]
+async fn audio_receiver_task(mut usb_audio_receiver: zerocopy_channel::Receiver<'static, NoopRawMutex, SampleBlock>) {
+    loop {
+        let _samples = usb_audio_receiver.receive().await;
+        // Use the samples, for example play back via the SAI peripheral.
+
+        // Notify the channel that the buffer is now ready to be reused
+        usb_audio_receiver.receive_done();
+    }
+}
+
+/// Receives audio samples from the host.
+#[embassy_executor::task]
+async fn usb_streaming_task(
+    mut stream: speaker::Stream<'static, usb::Driver<'static, peripherals::USB>>,
+    mut sender: zerocopy_channel::Sender<'static, NoopRawMutex, SampleBlock>,
+) {
+    loop {
+        stream.wait_connection().await;
+        info!("USB connected.");
+        _ = stream_handler(&mut stream, &mut sender).await;
+        info!("USB disconnected.");
+    }
+}
+
+/// Sends sample rate feedback to the host.
+///
+/// The `feedback_factor` scales the feedback timer's counter value so that the result is the number of samples that
+/// this device played back or "consumed" during one SOF period (1 ms) - in 10.14 format.
+///
+/// Ideally, the `feedback_factor` that is calculated below would be an integer for avoiding numerical errors.
+/// This is achieved by having `TICKS_PER_SAMPLE` be a power of two. For audio applications at a sample rate of 48 kHz,
+/// 24.576 MHz would be one such option.
+#[embassy_executor::task]
+async fn usb_feedback_task(mut feedback: speaker::Feedback<'static, usb::Driver<'static, peripherals::USB>>) {
+    let feedback_factor =
+        ((1 << FEEDBACK_SHIFT) as f32 / TICKS_PER_SAMPLE) / FEEDBACK_REFRESH_PERIOD.frame_count() as f32;
+
+    loop {
+        feedback.wait_connection().await;
+        _ = feedback_handler(&mut feedback, feedback_factor).await;
+    }
+}
+
+#[embassy_executor::task]
+async fn usb_task(mut usb_device: embassy_usb::UsbDevice<'static, usb::Driver<'static, peripherals::USB>>) {
+    usb_device.run().await;
+}
+
+/// Checks for changes on the control monitor of the class.
+///
+/// In this case, monitor changes of volume or mute state.
+#[embassy_executor::task]
+async fn usb_control_task(control_monitor: speaker::ControlMonitor<'static>) {
+    loop {
+        control_monitor.changed().await;
+
+        for channel in AUDIO_CHANNELS {
+            let volume = control_monitor.volume(channel).unwrap();
+            info!("Volume changed to {} on channel {}.", volume, channel);
+        }
+    }
+}
+
+/// Feedback value measurement and calculation
+///
+/// Used for measuring/calculating the number of samples that were received from the host during the
+/// `FEEDBACK_REFRESH_PERIOD`.
+///
+/// Configured in this example with
+/// - a refresh period of 8 ms, and
+/// - a tick rate of 42 MHz.
+///
+/// This gives an (ideal) counter value of 336.000 for every update of the `FEEDBACK_SIGNAL`.
+#[interrupt]
+fn TIM5() {
+    static mut LAST_TICKS: u32 = 0;
+    static mut FRAME_COUNT: usize = 0;
+
+    critical_section::with(|cs| {
+        // Read timer counter.
+        let ticks = TIMER.borrow(cs).borrow().as_ref().unwrap().regs_gp32().cnt().read();
+
+        // Clear trigger interrupt flag.
+        TIMER
+            .borrow(cs)
+            .borrow_mut()
+            .as_mut()
+            .unwrap()
+            .regs_gp32()
+            .sr()
+            .modify(|r| r.set_tif(false));
+
+        // Count up frames and emit a signal, when the refresh period is reached (here, every 8 ms).
+        *FRAME_COUNT += 1;
+        if *FRAME_COUNT >= FEEDBACK_REFRESH_PERIOD.frame_count() {
+            *FRAME_COUNT = 0;
+            FEEDBACK_SIGNAL.signal(ticks.wrapping_sub(*LAST_TICKS));
+            *LAST_TICKS = ticks;
+        }
+    });
+}
+
+// If you are trying this and your USB device doesn't connect, the most
+// common issues are the RCC config and vbus_detection
+//
+// See https://embassy.dev/book/#_the_usb_examples_are_not_working_on_my_board_is_there_anything_else_i_need_to_configure
+// for more information.
+#[embassy_executor::main]
+async fn main(spawner: Spawner) {
+    let mut config = Config::default();
+    {
+        use embassy_stm32::rcc::*;
+        config.rcc.hsi = None;
+        config.rcc.hsi48 = Some(Hsi48Config { sync_from_usb: true }); // needed for USB
+        config.rcc.hse = Some(Hse {
+            freq: Hertz(8_000_000),
+            mode: HseMode::BypassDigital,
+        });
+        config.rcc.pll1 = Some(Pll {
+            source: PllSource::HSE,
+            prediv: PllPreDiv::DIV2,
+            mul: PllMul::MUL125,
+            divp: Some(PllDiv::DIV2), // 250 Mhz
+            divq: None,
+            divr: None,
+        });
+        config.rcc.pll2 = Some(Pll {
+            source: PllSource::HSE,
+            prediv: PllPreDiv::DIV4,
+            mul: PllMul::MUL123,
+            divp: Some(PllDiv::DIV20), // 12.3 Mhz, close to 12.288 MHz for 48 kHz audio
+            divq: None,
+            divr: None,
+        });
+        config.rcc.ahb_pre = AHBPrescaler::DIV2;
+        config.rcc.apb1_pre = APBPrescaler::DIV4;
+        config.rcc.apb2_pre = APBPrescaler::DIV2;
+        config.rcc.apb3_pre = APBPrescaler::DIV4;
+        config.rcc.sys = Sysclk::PLL1_P;
+        config.rcc.voltage_scale = VoltageScale::Scale0;
+        config.rcc.mux.usbsel = mux::Usbsel::HSI48;
+        config.rcc.mux.sai2sel = mux::Saisel::PLL2_P;
+    }
+    let p = embassy_stm32::init(config);
+
+    info!("Hello World!");
+
+    // Configure all required buffers in a static way.
+    debug!("USB packet size is {} byte", USB_MAX_PACKET_SIZE);
+    static CONFIG_DESCRIPTOR: StaticCell<[u8; 256]> = StaticCell::new();
+    let config_descriptor = CONFIG_DESCRIPTOR.init([0; 256]);
+
+    static BOS_DESCRIPTOR: StaticCell<[u8; 32]> = StaticCell::new();
+    let bos_descriptor = BOS_DESCRIPTOR.init([0; 32]);
+
+    const CONTROL_BUF_SIZE: usize = 64;
+    static CONTROL_BUF: StaticCell<[u8; CONTROL_BUF_SIZE]> = StaticCell::new();
+    let control_buf = CONTROL_BUF.init([0; CONTROL_BUF_SIZE]);
+
+    static STATE: StaticCell<speaker::State> = StaticCell::new();
+    let state = STATE.init(speaker::State::new());
+
+    let usb_driver = usb::Driver::new(p.USB, Irqs, p.PA12, p.PA11);
+
+    // Basic USB device configuration
+    let mut config = embassy_usb::Config::new(0xc0de, 0xcafe);
+    config.manufacturer = Some("Embassy");
+    config.product = Some("USB-audio-speaker example");
+    config.serial_number = Some("12345678");
+
+    // Required for windows compatibility.
+    // https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/kconfig/CONFIG_CDC_ACM_IAD.html#help
+    config.device_class = 0xEF;
+    config.device_sub_class = 0x02;
+    config.device_protocol = 0x01;
+    config.composite_with_iads = true;
+
+    let mut builder = embassy_usb::Builder::new(
+        usb_driver,
+        config,
+        config_descriptor,
+        bos_descriptor,
+        &mut [], // no msos descriptors
+        control_buf,
+    );
+
+    // Create the UAC1 Speaker class components
+    let (stream, feedback, control_monitor) = Speaker::new(
+        &mut builder,
+        state,
+        USB_MAX_PACKET_SIZE as u16,
+        uac1::SampleWidth::Width4Byte,
+        &[SAMPLE_RATE_HZ],
+        &AUDIO_CHANNELS,
+        FEEDBACK_REFRESH_PERIOD,
+    );
+
+    // Create the USB device
+    let usb_device = builder.build();
+
+    // Establish a zero-copy channel for transferring received audio samples between tasks
+    static SAMPLE_BLOCKS: StaticCell<[SampleBlock; 2]> = StaticCell::new();
+    let sample_blocks = SAMPLE_BLOCKS.init([Vec::new(), Vec::new()]);
+
+    static CHANNEL: StaticCell<zerocopy_channel::Channel<'_, NoopRawMutex, SampleBlock>> = StaticCell::new();
+    let channel = CHANNEL.init(zerocopy_channel::Channel::new(sample_blocks));
+    let (sender, receiver) = channel.split();
+
+    // Run a timer for counting between SOF interrupts.
+    let mut tim5 = timer::low_level::Timer::new(p.TIM5);
+    tim5.set_tick_freq(Hertz(FEEDBACK_COUNTER_TICK_RATE));
+    tim5.set_trigger_source(timer::low_level::TriggerSource::ITR12); // The USB SOF signal.
+    tim5.set_slave_mode(timer::low_level::SlaveMode::TRIGGER_MODE);
+    tim5.regs_gp16().dier().modify(|r| r.set_tie(true)); // Enable the trigger interrupt.
+    tim5.start();
+
+    TIMER.lock(|p| p.borrow_mut().replace(tim5));
+
+    // Unmask the TIM5 interrupt.
+    unsafe {
+        cortex_m::peripheral::NVIC::unmask(interrupt::TIM5);
+    }
+
+    // Launch USB audio tasks.
+    unwrap!(spawner.spawn(usb_control_task(control_monitor)));
+    unwrap!(spawner.spawn(usb_streaming_task(stream, sender)));
+    unwrap!(spawner.spawn(usb_feedback_task(feedback)));
+    unwrap!(spawner.spawn(usb_task(usb_device)));
+    unwrap!(spawner.spawn(audio_receiver_task(receiver)));
+}