1 files changed, 75 insertions, 0 deletions

diff --git a/examples/mimxrt1011/src/lib.rs b/examples/mimxrt1011/src/lib.rs
new file mode 100644
index 000000000..f0391ef57
--- /dev/null
+++ b/examples/mimxrt1011/src/lib.rs
@@ -0,0 +1,75 @@
+//! FlexSPI configuration block (FCB) for iMXRT1011 boards.
+//!
+//! This is a generic FCB that should work with most QSPI flash.
+
+#![no_std]
+
+use imxrt_boot_gen::flexspi;
+use imxrt_boot_gen::flexspi::opcodes::sdr::*;
+use imxrt_boot_gen::flexspi::{
+    ColumnAddressWidth, Command, DeviceModeConfiguration, FlashPadType, Instr, LookupTable, Pads,
+    ReadSampleClockSource, Sequence, SequenceBuilder, SerialClockFrequency, SerialFlashRegion,
+    WaitTimeConfigurationCommands,
+};
+use imxrt_boot_gen::serial_flash::nor;
+
+/// While the IMXRT1010-EVK and Makerdiary iMX RT1011 Nano Kit have 128MBit of flash we limit to 64Mbit
+/// to allow the Metro M7 boards to use the same FCB configuration.
+const DENSITY_BITS: u32 = 64 * 1024 * 1024;
+const DENSITY_BYTES: u32 = DENSITY_BITS / 8;
+
+const SEQ_READ: Sequence = SequenceBuilder::new()
+    .instr(Instr::new(CMD, Pads::One, 0xEB))
+    .instr(Instr::new(RADDR, Pads::Four, 0x18))
+    .instr(Instr::new(DUMMY, Pads::Four, 0x06))
+    .instr(Instr::new(READ, Pads::Four, 0x04))
+    .build();
+
+const SEQ_READ_STATUS: Sequence = SequenceBuilder::new()
+    .instr(Instr::new(CMD, Pads::One, 0x05))
+    .instr(Instr::new(READ, Pads::One, 0x01))
+    .build();
+
+const SEQ_WRITE_ENABLE: Sequence = SequenceBuilder::new().instr(Instr::new(CMD, Pads::One, 0x06)).build();
+
+const SEQ_ERASE_SECTOR: Sequence = SequenceBuilder::new()
+    .instr(Instr::new(CMD, Pads::One, 0x20))
+    .instr(Instr::new(RADDR, Pads::One, 0x18))
+    .build();
+
+const SEQ_PAGE_PROGRAM: Sequence = SequenceBuilder::new()
+    .instr(Instr::new(CMD, Pads::One, 0x02))
+    .instr(Instr::new(RADDR, Pads::One, 0x18))
+    .instr(Instr::new(WRITE, Pads::One, 0x04))
+    .build();
+
+const SEQ_CHIP_ERASE: Sequence = SequenceBuilder::new().instr(Instr::new(CMD, Pads::One, 0x60)).build();
+
+const LUT: LookupTable = LookupTable::new()
+    .command(Command::Read, SEQ_READ)
+    .command(Command::ReadStatus, SEQ_READ_STATUS)
+    .command(Command::WriteEnable, SEQ_WRITE_ENABLE)
+    .command(Command::EraseSector, SEQ_ERASE_SECTOR)
+    .command(Command::PageProgram, SEQ_PAGE_PROGRAM)
+    .command(Command::ChipErase, SEQ_CHIP_ERASE);
+
+const COMMON_CONFIGURATION_BLOCK: flexspi::ConfigurationBlock = flexspi::ConfigurationBlock::new(LUT)
+    .read_sample_clk_src(ReadSampleClockSource::LoopbackFromDQSPad)
+    .cs_hold_time(0x03)
+    .cs_setup_time(0x03)
+    .column_address_width(ColumnAddressWidth::OtherDevices)
+    .device_mode_configuration(DeviceModeConfiguration::Disabled)
+    .wait_time_cfg_commands(WaitTimeConfigurationCommands::disable())
+    .flash_size(SerialFlashRegion::A1, DENSITY_BYTES)
+    .serial_clk_freq(SerialClockFrequency::MHz120)
+    .serial_flash_pad_type(FlashPadType::Quad);
+
+pub const SERIAL_NOR_CONFIGURATION_BLOCK: nor::ConfigurationBlock =
+    nor::ConfigurationBlock::new(COMMON_CONFIGURATION_BLOCK)
+        .page_size(256)
+        .sector_size(4096)
+        .ip_cmd_serial_clk_freq(nor::SerialClockFrequency::MHz30);
+
+#[unsafe(no_mangle)]
+#[cfg_attr(all(target_arch = "arm", target_os = "none"), link_section = ".fcb")]
+pub static FLEXSPI_CONFIGURATION_BLOCK: nor::ConfigurationBlock = SERIAL_NOR_CONFIGURATION_BLOCK;