4 files changed, 9 insertions, 9 deletions

diff --git a/examples/stm32f1/src/bin/adc.rs b/examples/stm32f1/src/bin/adc.rs
index 30947c3c2..1edac3d83 100644
--- a/examples/stm32f1/src/bin/adc.rs
+++ b/examples/stm32f1/src/bin/adc.rs
@@ -7,7 +7,7 @@ use embassy_executor::Spawner;
 use embassy_stm32::adc::Adc;
 use embassy_stm32::peripherals::ADC1;
 use embassy_stm32::{adc, bind_interrupts};
-use embassy_time::{Delay, Duration, Timer};
+use embassy_time::{Delay, Timer};
 use {defmt_rtt as _, panic_probe as _};
 
 bind_interrupts!(struct Irqs {
@@ -35,6 +35,6 @@ async fn main(_spawner: Spawner) {
     loop {
         let v = adc.read(&mut pin).await;
         info!("--> {} - {} mV", v, convert_to_millivolts(v));
-        Timer::after(Duration::from_millis(100)).await;
+        Timer::after_millis(100).await;
     }
 }
diff --git a/examples/stm32f1/src/bin/blinky.rs b/examples/stm32f1/src/bin/blinky.rs
index b9b0ac238..3425b0536 100644
--- a/examples/stm32f1/src/bin/blinky.rs
+++ b/examples/stm32f1/src/bin/blinky.rs
@@ -5,7 +5,7 @@
 use defmt::*;
 use embassy_executor::Spawner;
 use embassy_stm32::gpio::{Level, Output, Speed};
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use {defmt_rtt as _, panic_probe as _};
 
 #[embassy_executor::main]
@@ -18,10 +18,10 @@ async fn main(_spawner: Spawner) {
     loop {
         info!("high");
         led.set_high();
-        Timer::after(Duration::from_millis(300)).await;
+        Timer::after_millis(300).await;
 
         info!("low");
         led.set_low();
-        Timer::after(Duration::from_millis(300)).await;
+        Timer::after_millis(300).await;
     }
 }
diff --git a/examples/stm32f1/src/bin/hello.rs b/examples/stm32f1/src/bin/hello.rs
index 180b6aabd..e63bcaae0 100644
--- a/examples/stm32f1/src/bin/hello.rs
+++ b/examples/stm32f1/src/bin/hello.rs
@@ -6,7 +6,7 @@ use defmt::info;
 use embassy_executor::Spawner;
 use embassy_stm32::time::Hertz;
 use embassy_stm32::Config;
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use {defmt_rtt as _, panic_probe as _};
 
 #[embassy_executor::main]
@@ -17,6 +17,6 @@ async fn main(_spawner: Spawner) -> ! {
 
     loop {
         info!("Hello World!");
-        Timer::after(Duration::from_secs(1)).await;
+        Timer::after_secs(1).await;
     }
 }
diff --git a/examples/stm32f1/src/bin/usb_serial.rs b/examples/stm32f1/src/bin/usb_serial.rs
index 663099ff7..60eb5d0e4 100644
--- a/examples/stm32f1/src/bin/usb_serial.rs
+++ b/examples/stm32f1/src/bin/usb_serial.rs
@@ -9,7 +9,7 @@ use embassy_stm32::gpio::{Level, Output, Speed};
 use embassy_stm32::time::Hertz;
 use embassy_stm32::usb::{Driver, Instance};
 use embassy_stm32::{bind_interrupts, peripherals, usb, Config};
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use embassy_usb::class::cdc_acm::{CdcAcmClass, State};
 use embassy_usb::driver::EndpointError;
 use embassy_usb::Builder;
@@ -35,7 +35,7 @@ async fn main(_spawner: Spawner) {
         // This forced reset is needed only for development, without it host
         // will not reset your device when you upload new firmware.
         let _dp = Output::new(&mut p.PA12, Level::Low, Speed::Low);
-        Timer::after(Duration::from_millis(10)).await;
+        Timer::after_millis(10).await;
     }
 
     // Create the driver, from the HAL.