4 files changed, 30 insertions, 21 deletions

diff --git a/examples/stm32wl/src/bin/lora_lorawan.rs b/examples/stm32wl/src/bin/lora_lorawan.rs
index 1a271b2f2..e179c5ca1 100644
--- a/examples/stm32wl/src/bin/lora_lorawan.rs
+++ b/examples/stm32wl/src/bin/lora_lorawan.rs
@@ -7,12 +7,12 @@
 
 use defmt::info;
 use embassy_executor::Spawner;
-use embassy_lora::iv::Stm32wlInterfaceVariant;
+use embassy_lora::iv::{InterruptHandler, Stm32wlInterfaceVariant};
 use embassy_lora::LoraTimer;
 use embassy_stm32::gpio::{Level, Output, Pin, Speed};
 use embassy_stm32::rng::Rng;
 use embassy_stm32::spi::Spi;
-use embassy_stm32::{interrupt, into_ref, pac, Peripheral};
+use embassy_stm32::{bind_interrupts, pac};
 use embassy_time::Delay;
 use lora_phy::mod_params::*;
 use lora_phy::sx1261_2::SX1261_2;
@@ -24,6 +24,10 @@ use {defmt_rtt as _, panic_probe as _};
 
 const LORAWAN_REGION: region::Region = region::Region::EU868; // warning: set this appropriately for the region
 
+bind_interrupts!(struct Irqs{
+    SUBGHZ_RADIO => InterruptHandler;
+});
+
 #[embassy_executor::main]
 async fn main(_spawner: Spawner) {
     let mut config = embassy_stm32::Config::default();
@@ -35,13 +39,11 @@ async fn main(_spawner: Spawner) {
 
     let spi = Spi::new_subghz(p.SUBGHZSPI, p.DMA1_CH1, p.DMA1_CH2);
 
-    let irq = interrupt::take!(SUBGHZ_RADIO);
-    into_ref!(irq);
     // Set CTRL1 and CTRL3 for high-power transmission, while CTRL2 acts as an RF switch between tx and rx
     let _ctrl1 = Output::new(p.PC4.degrade(), Level::Low, Speed::High);
     let ctrl2 = Output::new(p.PC5.degrade(), Level::High, Speed::High);
     let _ctrl3 = Output::new(p.PC3.degrade(), Level::High, Speed::High);
-    let iv = Stm32wlInterfaceVariant::new(irq, None, Some(ctrl2)).unwrap();
+    let iv = Stm32wlInterfaceVariant::new(Irqs, None, Some(ctrl2)).unwrap();
 
     let mut delay = Delay;
 
diff --git a/examples/stm32wl/src/bin/lora_p2p_receive.rs b/examples/stm32wl/src/bin/lora_p2p_receive.rs
index 5e80e8f6a..d3f051b1c 100644
--- a/examples/stm32wl/src/bin/lora_p2p_receive.rs
+++ b/examples/stm32wl/src/bin/lora_p2p_receive.rs
@@ -7,10 +7,10 @@
 
 use defmt::info;
 use embassy_executor::Spawner;
-use embassy_lora::iv::Stm32wlInterfaceVariant;
+use embassy_lora::iv::{InterruptHandler, Stm32wlInterfaceVariant};
+use embassy_stm32::bind_interrupts;
 use embassy_stm32::gpio::{Level, Output, Pin, Speed};
 use embassy_stm32::spi::Spi;
-use embassy_stm32::{interrupt, into_ref, Peripheral};
 use embassy_time::{Delay, Duration, Timer};
 use lora_phy::mod_params::*;
 use lora_phy::sx1261_2::SX1261_2;
@@ -19,6 +19,10 @@ use {defmt_rtt as _, panic_probe as _};
 
 const LORA_FREQUENCY_IN_HZ: u32 = 903_900_000; // warning: set this appropriately for the region
 
+bind_interrupts!(struct Irqs{
+    SUBGHZ_RADIO => InterruptHandler;
+});
+
 #[embassy_executor::main]
 async fn main(_spawner: Spawner) {
     let mut config = embassy_stm32::Config::default();
@@ -27,13 +31,11 @@ async fn main(_spawner: Spawner) {
 
     let spi = Spi::new_subghz(p.SUBGHZSPI, p.DMA1_CH1, p.DMA1_CH2);
 
-    let irq = interrupt::take!(SUBGHZ_RADIO);
-    into_ref!(irq);
     // Set CTRL1 and CTRL3 for high-power transmission, while CTRL2 acts as an RF switch between tx and rx
     let _ctrl1 = Output::new(p.PC4.degrade(), Level::Low, Speed::High);
     let ctrl2 = Output::new(p.PC5.degrade(), Level::High, Speed::High);
     let _ctrl3 = Output::new(p.PC3.degrade(), Level::High, Speed::High);
-    let iv = Stm32wlInterfaceVariant::new(irq, None, Some(ctrl2)).unwrap();
+    let iv = Stm32wlInterfaceVariant::new(Irqs, None, Some(ctrl2)).unwrap();
 
     let mut delay = Delay;
 
diff --git a/examples/stm32wl/src/bin/lora_p2p_send.rs b/examples/stm32wl/src/bin/lora_p2p_send.rs
index e22c714bd..fc5205c85 100644
--- a/examples/stm32wl/src/bin/lora_p2p_send.rs
+++ b/examples/stm32wl/src/bin/lora_p2p_send.rs
@@ -7,10 +7,10 @@
 
 use defmt::info;
 use embassy_executor::Spawner;
-use embassy_lora::iv::Stm32wlInterfaceVariant;
+use embassy_lora::iv::{InterruptHandler, Stm32wlInterfaceVariant};
+use embassy_stm32::bind_interrupts;
 use embassy_stm32::gpio::{Level, Output, Pin, Speed};
 use embassy_stm32::spi::Spi;
-use embassy_stm32::{interrupt, into_ref, Peripheral};
 use embassy_time::Delay;
 use lora_phy::mod_params::*;
 use lora_phy::sx1261_2::SX1261_2;
@@ -19,6 +19,10 @@ use {defmt_rtt as _, panic_probe as _};
 
 const LORA_FREQUENCY_IN_HZ: u32 = 903_900_000; // warning: set this appropriately for the region
 
+bind_interrupts!(struct Irqs{
+    SUBGHZ_RADIO => InterruptHandler;
+});
+
 #[embassy_executor::main]
 async fn main(_spawner: Spawner) {
     let mut config = embassy_stm32::Config::default();
@@ -27,13 +31,11 @@ async fn main(_spawner: Spawner) {
 
     let spi = Spi::new_subghz(p.SUBGHZSPI, p.DMA1_CH1, p.DMA1_CH2);
 
-    let irq = interrupt::take!(SUBGHZ_RADIO);
-    into_ref!(irq);
     // Set CTRL1 and CTRL3 for high-power transmission, while CTRL2 acts as an RF switch between tx and rx
     let _ctrl1 = Output::new(p.PC4.degrade(), Level::Low, Speed::High);
     let ctrl2 = Output::new(p.PC5.degrade(), Level::High, Speed::High);
     let _ctrl3 = Output::new(p.PC3.degrade(), Level::High, Speed::High);
-    let iv = Stm32wlInterfaceVariant::new(irq, None, Some(ctrl2)).unwrap();
+    let iv = Stm32wlInterfaceVariant::new(Irqs, None, Some(ctrl2)).unwrap();
 
     let mut delay = Delay;
 
diff --git a/examples/stm32wl/src/bin/uart_async.rs b/examples/stm32wl/src/bin/uart_async.rs
index ac8766af6..07b0f9d2c 100644
--- a/examples/stm32wl/src/bin/uart_async.rs
+++ b/examples/stm32wl/src/bin/uart_async.rs
@@ -4,10 +4,15 @@
 
 use defmt::*;
 use embassy_executor::Spawner;
-use embassy_stm32::interrupt;
-use embassy_stm32::usart::{Config, Uart};
+use embassy_stm32::usart::{Config, InterruptHandler, Uart};
+use embassy_stm32::{bind_interrupts, peripherals};
 use {defmt_rtt as _, panic_probe as _};
 
+bind_interrupts!(struct Irqs{
+    USART1 => InterruptHandler<peripherals::USART1>;
+    LPUART1 => InterruptHandler<peripherals::LPUART1>;
+});
+
 /*
 Pass Incoming data from LPUART1 to USART1
 Example is written for the LoRa-E5 mini v1.0,
@@ -28,12 +33,10 @@ async fn main(_spawner: Spawner) {
     config2.baudrate = 9600;
 
     //RX/TX connected to USB/UART Bridge on LoRa-E5 mini v1.0
-    let irq = interrupt::take!(USART1);
-    let mut usart1 = Uart::new(p.USART1, p.PB7, p.PB6, irq, p.DMA1_CH3, p.DMA1_CH4, config1);
+    let mut usart1 = Uart::new(p.USART1, p.PB7, p.PB6, Irqs, p.DMA1_CH3, p.DMA1_CH4, config1);
 
     //RX1/TX1 (LPUART) on LoRa-E5 mini v1.0
-    let irq = interrupt::take!(LPUART1);
-    let mut usart2 = Uart::new(p.LPUART1, p.PC0, p.PC1, irq, p.DMA1_CH5, p.DMA1_CH6, config2);
+    let mut usart2 = Uart::new(p.LPUART1, p.PC0, p.PC1, Irqs, p.DMA1_CH5, p.DMA1_CH6, config2);
 
     unwrap!(usart1.write(b"Hello Embassy World!\r\n").await);
     unwrap!(usart2.write(b"Hello Embassy World!\r\n").await);