1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
|
//! FlexSPI configuration block (FCB) for the iMXRT1060-EVK
//!
//! This uses IS25WP QuadSPI flash.
#![no_std]
use imxrt_boot_gen::flexspi::opcodes::sdr::*;
use imxrt_boot_gen::flexspi::{self, FlashPadType, ReadSampleClockSource, SerialClockFrequency, SerialFlashRegion, *};
use imxrt_boot_gen::serial_flash::*;
pub use nor::ConfigurationBlock;
const SEQ_READ: Sequence = SequenceBuilder::new()
.instr(Instr::new(CMD, Pads::One, 0xEB))
.instr(Instr::new(RADDR, Pads::Four, 0x18))
.instr(Instr::new(DUMMY, Pads::Four, 0x06))
.instr(Instr::new(READ, Pads::Four, 0x04))
.build();
const SEQ_READ_STATUS: Sequence = SequenceBuilder::new()
.instr(Instr::new(CMD, Pads::One, 0x05))
.instr(Instr::new(READ, Pads::One, 0x04))
.build();
const SEQ_WRITE_ENABLE: Sequence = SequenceBuilder::new().instr(Instr::new(CMD, Pads::One, 0x06)).build();
const SEQ_ERASE_SECTOR: Sequence = SequenceBuilder::new()
.instr(Instr::new(CMD, Pads::One, 0x20))
.instr(Instr::new(RADDR, Pads::One, 0x18))
.build();
const SEQ_PAGE_PROGRAM: Sequence = SequenceBuilder::new()
.instr(Instr::new(CMD, Pads::One, 0x02))
.instr(Instr::new(RADDR, Pads::One, 0x18))
.instr(Instr::new(WRITE, Pads::One, 0x04))
.build();
const SEQ_CHIP_ERASE: Sequence = SequenceBuilder::new().instr(Instr::new(CMD, Pads::One, 0x60)).build();
const LUT: LookupTable = LookupTable::new()
.command(Command::Read, SEQ_READ)
.command(Command::ReadStatus, SEQ_READ_STATUS)
.command(Command::WriteEnable, SEQ_WRITE_ENABLE)
.command(Command::EraseSector, SEQ_ERASE_SECTOR)
.command(Command::PageProgram, SEQ_PAGE_PROGRAM)
.command(Command::ChipErase, SEQ_CHIP_ERASE);
const COMMON_CONFIGURATION_BLOCK: flexspi::ConfigurationBlock = flexspi::ConfigurationBlock::new(LUT)
.version(Version::new(1, 4, 0))
.read_sample_clk_src(ReadSampleClockSource::LoopbackFromDQSPad)
.cs_hold_time(3)
.cs_setup_time(3)
.controller_misc_options(0x10)
.serial_flash_pad_type(FlashPadType::Quad)
.serial_clk_freq(SerialClockFrequency::MHz133)
.flash_size(SerialFlashRegion::A1, 8 * 1024 * 1024);
pub const SERIAL_NOR_CONFIGURATION_BLOCK: nor::ConfigurationBlock =
nor::ConfigurationBlock::new(COMMON_CONFIGURATION_BLOCK)
.page_size(256)
.sector_size(4096)
.ip_cmd_serial_clk_freq(nor::SerialClockFrequency::MHz30);
#[unsafe(no_mangle)]
#[cfg_attr(all(target_arch = "arm", target_os = "none"), unsafe(link_section = ".fcb"))]
pub static FLEXSPI_CONFIGURATION_BLOCK: nor::ConfigurationBlock = SERIAL_NOR_CONFIGURATION_BLOCK;
|
