1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
|
#![no_std]
#![no_main]
use defmt::*;
use embassy_stm32::Config;
use embassy_stm32::adc::{Adc, AdcChannel, SampleTime, adc4};
use embassy_stm32::rcc::{
AHB5Prescaler, AHBPrescaler, APBPrescaler, PllDiv, PllMul, PllPreDiv, PllSource, Sysclk, VoltageScale,
};
use {defmt_rtt as _, panic_probe as _};
#[embassy_executor::main]
async fn main(_spawner: embassy_executor::Spawner) {
let mut config = Config::default();
// Fine-tune PLL1 dividers/multipliers
config.rcc.pll1 = Some(embassy_stm32::rcc::Pll {
source: PllSource::HSI,
prediv: PllPreDiv::DIV1, // PLLM = 1 → HSI / 1 = 16 MHz
mul: PllMul::MUL30, // PLLN = 30 → 16 MHz * 30 = 480 MHz VCO
divr: Some(PllDiv::DIV5), // PLLR = 5 → 96 MHz (Sysclk)
// divq: Some(PllDiv::DIV10), // PLLQ = 10 → 48 MHz (NOT USED)
divq: None,
divp: Some(PllDiv::DIV30), // PLLP = 30 → 16 MHz (USBOTG)
frac: Some(0), // Fractional part (enabled)
});
config.rcc.ahb_pre = AHBPrescaler::DIV1;
config.rcc.apb1_pre = APBPrescaler::DIV1;
config.rcc.apb2_pre = APBPrescaler::DIV1;
config.rcc.apb7_pre = APBPrescaler::DIV1;
config.rcc.ahb5_pre = AHB5Prescaler::DIV4;
// voltage scale for max performance
config.rcc.voltage_scale = VoltageScale::RANGE1;
// route PLL1_P into the USB‐OTG‐HS block
config.rcc.sys = Sysclk::PLL1_R;
let mut p = embassy_stm32::init(config);
// **** ADC4 init ****
let mut adc4 = Adc::new_adc4(p.ADC4);
let mut adc4_pin1 = p.PA0; // A4
let mut adc4_pin2 = p.PA1; // A5
adc4.set_resolution_adc4(adc4::Resolution::BITS12);
adc4.set_averaging_adc4(adc4::Averaging::Samples256);
let max4 = adc4::resolution_to_max_count(adc4::Resolution::BITS12);
// **** ADC4 blocking read ****
let raw: u16 = adc4.blocking_read(&mut adc4_pin1, adc4::SampleTime::CYCLES1_5);
let volt: f32 = 3.0 * raw as f32 / max4 as f32;
info!("Read adc4 pin 1 {}", volt);
let raw: u16 = adc4.blocking_read(&mut adc4_pin2, adc4::SampleTime::CYCLES1_5);
let volt: f32 = 3.3 * raw as f32 / max4 as f32;
info!("Read adc4 pin 2 {}", volt);
// **** ADC4 async read ****
let mut degraded41 = adc4_pin1.degrade_adc();
let mut degraded42 = adc4_pin2.degrade_adc();
let mut measurements = [0u16; 2];
// The channels must be in ascending order and can't repeat for ADC4
adc4.read(
p.GPDMA1_CH1.reborrow(),
[
(&mut degraded42, SampleTime::CYCLES12_5),
(&mut degraded41, SampleTime::CYCLES12_5),
]
.into_iter(),
&mut measurements,
)
.await;
let volt2: f32 = 3.3 * measurements[0] as f32 / max4 as f32;
let volt1: f32 = 3.0 * measurements[1] as f32 / max4 as f32;
info!("Async read 4 pin 1 {}", volt1);
info!("Async read 4 pin 2 {}", volt2);
}
|
