6 files changed, 143 insertions, 18 deletions

diff --git a/examples/stm32wba6/src/bin/adc.rs b/examples/stm32wba6/src/bin/adc.rs
index a9651d57e..51dcff57a 100644
--- a/examples/stm32wba6/src/bin/adc.rs
+++ b/examples/stm32wba6/src/bin/adc.rs
@@ -2,30 +2,55 @@
 #![no_main]
 
 use defmt::*;
-use embassy_stm32::adc::{adc4, AdcChannel};
+use embassy_stm32::Config;
+use embassy_stm32::adc::{Adc, AdcChannel, SampleTime, adc4};
+use embassy_stm32::rcc::{
+    AHB5Prescaler, AHBPrescaler, APBPrescaler, PllDiv, PllMul, PllPreDiv, PllSource, Sysclk, VoltageScale,
+};
 use {defmt_rtt as _, panic_probe as _};
 
 #[embassy_executor::main]
 async fn main(_spawner: embassy_executor::Spawner) {
-    let config = embassy_stm32::Config::default();
+    let mut config = Config::default();
+    // Fine-tune PLL1 dividers/multipliers
+    config.rcc.pll1 = Some(embassy_stm32::rcc::Pll {
+        source: PllSource::HSI,
+        prediv: PllPreDiv::DIV1,  // PLLM = 1 → HSI / 1 = 16 MHz
+        mul: PllMul::MUL30,       // PLLN = 30 → 16 MHz * 30 = 480 MHz VCO
+        divr: Some(PllDiv::DIV5), // PLLR = 5 → 96 MHz (Sysclk)
+        // divq: Some(PllDiv::DIV10), // PLLQ = 10 → 48 MHz (NOT USED)
+        divq: None,
+        divp: Some(PllDiv::DIV30), // PLLP = 30 → 16 MHz (USBOTG)
+        frac: Some(0),             // Fractional part (enabled)
+    });
+
+    config.rcc.ahb_pre = AHBPrescaler::DIV1;
+    config.rcc.apb1_pre = APBPrescaler::DIV1;
+    config.rcc.apb2_pre = APBPrescaler::DIV1;
+    config.rcc.apb7_pre = APBPrescaler::DIV1;
+    config.rcc.ahb5_pre = AHB5Prescaler::DIV4;
+
+    // voltage scale for max performance
+    config.rcc.voltage_scale = VoltageScale::RANGE1;
+    // route PLL1_P into the USB‐OTG‐HS block
+    config.rcc.sys = Sysclk::PLL1_R;
 
     let mut p = embassy_stm32::init(config);
 
     // **** ADC4 init ****
-    let mut adc4 = adc4::Adc4::new(p.ADC4);
+    let mut adc4 = Adc::new_adc4(p.ADC4);
     let mut adc4_pin1 = p.PA0; // A4
     let mut adc4_pin2 = p.PA1; // A5
-    adc4.set_resolution(adc4::Resolution::BITS12);
-    adc4.set_averaging(adc4::Averaging::Samples256);
-    adc4.set_sample_time(adc4::SampleTime::CYCLES1_5);
+    adc4.set_resolution_adc4(adc4::Resolution::BITS12);
+    adc4.set_averaging_adc4(adc4::Averaging::Samples256);
     let max4 = adc4::resolution_to_max_count(adc4::Resolution::BITS12);
 
     // **** ADC4 blocking read ****
-    let raw: u16 = adc4.blocking_read(&mut adc4_pin1);
+    let raw: u16 = adc4.blocking_read(&mut adc4_pin1, adc4::SampleTime::CYCLES1_5);
     let volt: f32 = 3.0 * raw as f32 / max4 as f32;
     info!("Read adc4 pin 1 {}", volt);
 
-    let raw: u16 = adc4.blocking_read(&mut adc4_pin2);
+    let raw: u16 = adc4.blocking_read(&mut adc4_pin2, adc4::SampleTime::CYCLES1_5);
     let volt: f32 = 3.3 * raw as f32 / max4 as f32;
     info!("Read adc4 pin 2 {}", volt);
 
@@ -37,11 +62,14 @@ async fn main(_spawner: embassy_executor::Spawner) {
     // The channels must be in ascending order and can't repeat for ADC4
     adc4.read(
         p.GPDMA1_CH1.reborrow(),
-        [&mut degraded42, &mut degraded41].into_iter(),
+        [
+            (&mut degraded42, SampleTime::CYCLES12_5),
+            (&mut degraded41, SampleTime::CYCLES12_5),
+        ]
+        .into_iter(),
         &mut measurements,
     )
-    .await
-    .unwrap();
+    .await;
     let volt2: f32 = 3.3 * measurements[0] as f32 / max4 as f32;
     let volt1: f32 = 3.0 * measurements[1] as f32 / max4 as f32;
     info!("Async read 4 pin 1 {}", volt1);
diff --git a/examples/stm32wba6/src/bin/blinky.rs b/examples/stm32wba6/src/bin/blinky.rs
index 0d803b257..95f3339b7 100644
--- a/examples/stm32wba6/src/bin/blinky.rs
+++ b/examples/stm32wba6/src/bin/blinky.rs
@@ -3,16 +3,45 @@
 
 use defmt::*;
 use embassy_executor::Spawner;
+use embassy_stm32::Config;
 use embassy_stm32::gpio::{Level, Output, Speed};
+use embassy_stm32::rcc::{
+    AHB5Prescaler, AHBPrescaler, APBPrescaler, PllDiv, PllMul, PllPreDiv, PllSource, Sysclk, VoltageScale,
+};
 use embassy_time::Timer;
 use {defmt_rtt as _, panic_probe as _};
 
 #[embassy_executor::main]
 async fn main(_spawner: Spawner) {
-    let p = embassy_stm32::init(Default::default());
+    let mut config = Config::default();
+    // Fine-tune PLL1 dividers/multipliers
+    config.rcc.pll1 = Some(embassy_stm32::rcc::Pll {
+        source: PllSource::HSI,
+        prediv: PllPreDiv::DIV1,  // PLLM = 1 → HSI / 1 = 16 MHz
+        mul: PllMul::MUL30,       // PLLN = 30 → 16 MHz * 30 = 480 MHz VCO
+        divr: Some(PllDiv::DIV5), // PLLR = 5 → 96 MHz (Sysclk)
+        // divq: Some(PllDiv::DIV10), // PLLQ = 10 → 48 MHz (NOT USED)
+        divq: None,
+        divp: Some(PllDiv::DIV30), // PLLP = 30 → 16 MHz (USBOTG)
+        frac: Some(0),             // Fractional part (enabled)
+    });
+
+    config.rcc.ahb_pre = AHBPrescaler::DIV1;
+    config.rcc.apb1_pre = APBPrescaler::DIV1;
+    config.rcc.apb2_pre = APBPrescaler::DIV1;
+    config.rcc.apb7_pre = APBPrescaler::DIV1;
+    config.rcc.ahb5_pre = AHB5Prescaler::DIV4;
+
+    // voltage scale for max performance
+    config.rcc.voltage_scale = VoltageScale::RANGE1;
+    // route PLL1_P into the USB‐OTG‐HS block
+    config.rcc.sys = Sysclk::PLL1_R;
+
+    let p = embassy_stm32::init(config);
     info!("Hello World!");
 
-    let mut led = Output::new(p.PB4, Level::High, Speed::Low);
+    // LD2 - PC4
+    let mut led = Output::new(p.PC4, Level::High, Speed::Low);
 
     loop {
         info!("high");
diff --git a/examples/stm32wba6/src/bin/button_exti.rs b/examples/stm32wba6/src/bin/button_exti.rs
index 34a08bbc6..d63290d42 100644
--- a/examples/stm32wba6/src/bin/button_exti.rs
+++ b/examples/stm32wba6/src/bin/button_exti.rs
@@ -3,16 +3,22 @@
 
 use defmt::*;
 use embassy_executor::Spawner;
-use embassy_stm32::exti::ExtiInput;
+use embassy_stm32::exti::{self, ExtiInput};
 use embassy_stm32::gpio::Pull;
+use embassy_stm32::{bind_interrupts, interrupt};
 use {defmt_rtt as _, panic_probe as _};
 
+bind_interrupts!(
+    pub struct Irqs{
+        EXTI13 => exti::InterruptHandler<interrupt::typelevel::EXTI13>;
+});
+
 #[embassy_executor::main]
 async fn main(_spawner: Spawner) {
     let p = embassy_stm32::init(Default::default());
     info!("Hello World!");
 
-    let mut button = ExtiInput::new(p.PC13, p.EXTI13, Pull::Up);
+    let mut button = ExtiInput::new(p.PC13, p.EXTI13, Pull::Up, Irqs);
 
     info!("Press the USER button...");
 
diff --git a/examples/stm32wba6/src/bin/pwm.rs b/examples/stm32wba6/src/bin/pwm.rs
index 2c696834a..64ae01945 100644
--- a/examples/stm32wba6/src/bin/pwm.rs
+++ b/examples/stm32wba6/src/bin/pwm.rs
@@ -4,13 +4,13 @@
 use defmt::*;
 use defmt_rtt as _; // global logger
 use embassy_executor::Spawner;
+use embassy_stm32::Config;
 use embassy_stm32::gpio::OutputType;
 use embassy_stm32::rcc::{
     AHB5Prescaler, AHBPrescaler, APBPrescaler, PllDiv, PllMul, PllPreDiv, PllSource, Sysclk, VoltageScale,
 };
 use embassy_stm32::time::khz;
 use embassy_stm32::timer::simple_pwm::{PwmPin, SimplePwm};
-use embassy_stm32::Config;
 use embassy_time::Timer;
 use panic_probe as _;
 
diff --git a/examples/stm32wba6/src/bin/rtc.rs b/examples/stm32wba6/src/bin/rtc.rs
new file mode 100644
index 000000000..cef8501e0
--- /dev/null
+++ b/examples/stm32wba6/src/bin/rtc.rs
@@ -0,0 +1,62 @@
+#![no_std]
+#![no_main]
+
+use defmt::*;
+use embassy_executor::Spawner;
+use embassy_stm32::Config;
+use embassy_stm32::rcc::*;
+use embassy_stm32::rtc::{DateTime, DayOfWeek, Rtc, RtcConfig};
+use embassy_time::Timer;
+use {defmt_rtt as _, panic_probe as _};
+
+pub fn pll_init(config: &mut Config) {
+    config.rcc.pll1 = Some(embassy_stm32::rcc::Pll {
+        source: PllSource::HSI,
+        prediv: PllPreDiv::DIV1,  // PLLM = 1 → HSI / 1 = 16 MHz
+        mul: PllMul::MUL30,       // PLLN = 30 → 16 MHz * 30 = 480 MHz VCO
+        divr: Some(PllDiv::DIV5), // PLLR = 5 → 96 MHz (Sysclk)
+        // divq: Some(PllDiv::DIV10), // PLLQ = 10 → 48 MHz (NOT USED)
+        divq: None,
+        divp: Some(PllDiv::DIV30), // PLLP = 30 → 16 MHz (USBOTG)
+        frac: Some(0),             // Fractional part (enabled)
+    });
+
+    config.rcc.ahb_pre = AHBPrescaler::DIV1;
+    config.rcc.apb1_pre = APBPrescaler::DIV1;
+    config.rcc.apb2_pre = APBPrescaler::DIV1;
+    config.rcc.apb7_pre = APBPrescaler::DIV1;
+    config.rcc.ahb5_pre = AHB5Prescaler::DIV4;
+
+    // voltage scale for max performance
+    config.rcc.voltage_scale = VoltageScale::RANGE1;
+    // route PLL1_P into the USB‐OTG‐HS block
+    config.rcc.sys = Sysclk::PLL1_R;
+}
+
+#[embassy_executor::main]
+async fn main(_spawner: Spawner) {
+    let mut config = Config::default();
+
+    pll_init(&mut config);
+
+    let p = embassy_stm32::init(config);
+
+    let mut rtc = Rtc::new(p.RTC, RtcConfig::default());
+
+    // Setting datetime
+    let initial_datetime = DateTime::from(1970, 1, 1, DayOfWeek::Thursday, 0, 00, 00, 0).unwrap();
+    match rtc.0.set_datetime(initial_datetime) {
+        Ok(()) => info!("RTC set successfully."),
+        Err(e) => error!("Failed to set RTC date/time: {:?}", e),
+    }
+
+    // Reading datetime every 1s
+    loop {
+        match rtc.1.now() {
+            Ok(result) => info!("{}", result),
+            Err(e) => error!("Failed to set RTC date/time: {:?}", e),
+        }
+
+        Timer::after_millis(1000).await;
+    }
+}
diff --git a/examples/stm32wba6/src/bin/usb_hs_serial.rs b/examples/stm32wba6/src/bin/usb_hs_serial.rs
index 20bdeaac3..a60eeb480 100644
--- a/examples/stm32wba6/src/bin/usb_hs_serial.rs
+++ b/examples/stm32wba6/src/bin/usb_hs_serial.rs
@@ -5,10 +5,10 @@ use defmt::{panic, *};
 use embassy_executor::Spawner;
 use embassy_futures::join::join;
 use embassy_stm32::usb::{Driver, Instance};
-use embassy_stm32::{bind_interrupts, peripherals, usb, Config};
+use embassy_stm32::{Config, bind_interrupts, peripherals, usb};
+use embassy_usb::Builder;
 use embassy_usb::class::cdc_acm::{CdcAcmClass, State};
 use embassy_usb::driver::EndpointError;
-use embassy_usb::Builder;
 use {defmt_rtt as _, panic_probe as _};
 
 bind_interrupts!(struct Irqs {